25.04.2024, 11:13 UhrDeutsch | English
Hallo Gast [ Registrierung | Anmelden ]

Neues Thema eröffnen   Neue Antwort erstellen
Vorheriges Thema anzeigen Druckerfreundliche Version Einloggen, um private Nachrichten zu lesen Nächstes Thema anzeigen
Autor Nachricht
s-h-o-x
Titel: [gelöst] PVR 350, ich bekomme es nicht hin, ...  BeitragVerfasst am: 23.06.2006, 22:07 Uhr



Anmeldung: 18. Jun 2005
Beiträge: 30

hi,

ich habe kanotix-2006-easter-rc4.

ivtv-treiber sind ja schon dabei. habe dann die firmware-dateien in "/lib/firmware" kopiert >> meckert auch nicht.

ich kann aber mit "mplayer /dev/video0" nur ein schwarzes bild sehen, also gar nix, kein signal rauschen o.ä.

in den ivtv-meldungen wird auch ein fehler mit i2c hardware gemeldet. damit kann ich leider nichts anfangen.

hier mal der auszug:

Code:
ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.6.2 (tagged release) loading
ivtv:  Linux version: 2.6.16.16-kanotix-1 SMP preempt 586 gcc-4.0
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 18 (level, low) -> IRQ 169
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[169]  MMIO=[f7005000-f70057ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based)
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 20 (level, low) -> IRQ 193
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 201, io mem 0xfb000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 4-2: new low speed USB device using uhci_hcd and address 2
tveeprom 1-0050: Hauppauge model 48139, rev K257, serial# 8260564
tveeprom 1-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74)
tveeprom 1-0050: audio processor is MSP4418 (idx 25)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has radio, has IR remote
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
usb 4-2: new low speed USB device using uhci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
epic100.c:v1.11 1/7/2001 Written by Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/epic100.html
  (unofficial 2.4.x kernel port, version 1.11+LK1.1.14+AC1.1.14, June 2, 2004)
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
saa7127 1-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00508d000072023d]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
ts: Compaq touchscreen protocol output
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c addr 0x40 not found for command 0x40086d11!
ivtv0: i2c addr 0x40 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: i2c hardware 0x00000008 not found for command 0xc008561c!
ivtv0: Initialized Hauppauge WinTV PVR-350, card #0
ivtv:  ====================  END INIT IVTV  ====================


was kann ich da tuen? wer kann mir bitte helfen, würde so gerne mythtv benutzen Winken


Zuletzt bearbeitet von s-h-o-x am 25.06.2006, 13:16 Uhr, insgesamt ein Mal bearbeitet
 
 Benutzer-Profile anzeigen Private Nachricht senden ICQ-Nummer 
Antworten mit Zitat Nach oben
schnorrer
Titel: PVR 350, ich bekomme es nicht hin, die zu installieren...  BeitragVerfasst am: 23.06.2006, 23:18 Uhr



Anmeldung: 09. Jan 2006
Beiträge: 1720

entsprechend deinen Auszügen handelt es ich bei deiner Karte nicht um 1 Hauppuagge PVR-350.

lspci -n reicht um den saa7134 Chip zu finden.

Deine Karte dürfte ein USB-Model sein. Daher funktioniert nichts mit ivtv und der FW-für die PVR-350
 
 Benutzer-Profile anzeigen Private Nachricht senden  
Antworten mit Zitat Nach oben
s-h-o-x
Titel: verstehe ich nicht :?:  BeitragVerfasst am: 23.06.2006, 23:45 Uhr



Anmeldung: 18. Jun 2005
Beiträge: 30

ich habe doch aber eine pci-karte in den pc gesteckt und nichts am usb.

bei "lspci -n" kommt nur das hier:

Code:
0000:00:00.0 0600: 8086:2578 (rev 02)
0000:00:01.0 0604: 8086:2579 (rev 02)
0000:00:1d.0 0c03: 8086:24d2 (rev 02)
0000:00:1d.1 0c03: 8086:24d4 (rev 02)
0000:00:1d.2 0c03: 8086:24d7 (rev 02)
0000:00:1d.3 0c03: 8086:24de (rev 02)
0000:00:1d.7 0c03: 8086:24dd (rev 02)
0000:00:1e.0 0604: 8086:244e (rev c2)
0000:00:1f.0 0601: 8086:24d0 (rev 02)
0000:00:1f.2 0101: 8086:24d1 (rev 02)
0000:00:1f.3 0c05: 8086:24d3 (rev 02)
0000:00:1f.5 0401: 8086:24d5 (rev 02)
0000:01:00.0 0300: 102b:2527 (rev 01)
0000:02:02.0 0c00: 104c:8024
0000:02:04.0 0400: 4444:0803 (rev 01)
0000:02:05.0 0200: 10b8:0005 (rev 08)


falls du aber "lspci -m" meintest kommt dies hier:

Code:
Multimedia video controller Internext Compression Inc iTVC15 MPEG-2
 Encoder 01 00 Hauppauge computer works Inc. WinTV PVR-350


sorry, wenn ich's nicht kapiert habe... Traurig
 
 Benutzer-Profile anzeigen Private Nachricht senden ICQ-Nummer 
Antworten mit Zitat Nach oben
s-h-o-x
Titel: gelöst: falscher pci-steckplatz  BeitragVerfasst am: 25.06.2006, 13:20 Uhr



Anmeldung: 18. Jun 2005
Beiträge: 30

man, da hab ich ein paar tage gebraucht um mal das zu testen Winken

habe also die karte in einen anderen pci-steckplatz gesteckt und siehe da die funktioniert und ich kann jetzt tv sehen...

trotzdem vielen dank an euch!

der jetzt wieder etwas beruhigte s-h-o-x
 
 Benutzer-Profile anzeigen Private Nachricht senden ICQ-Nummer 
Antworten mit Zitat Nach oben
Beiträge vom vorherigen Thema anzeigen:     
Gehe zu:  
Alle Zeiten sind GMT + 1 Stunde
Neues Thema eröffnen   Neue Antwort erstellen
Vorheriges Thema anzeigen Druckerfreundliche Version Einloggen, um private Nachrichten zu lesen Nächstes Thema anzeigen
PNphpBB2 © 2003-2007 
 
Deutsch | English
Logos and trademarks are the property of their respective owners, comments are property of their posters, the rest is © 2004 - 2006 by Jörg Schirottke (Kano).
Consult Impressum and Legal Terms for details. Kanotix is Free Software released under the GNU/GPL license.
This CMS is powered by PostNuke, all themes used at this site are released under the GNU/GPL license. designed and hosted by w3you. Our web server is running on Kanotix64-2006.